THE ORIGINAL Stock Tank Pool DIY

Check out our blog for more details about this DIY!
(http://www.heywandererblog.com/2017/06/diy-stock-tank-pool-everything-you-need.html)
Instagram- http://www.instagram.com/heywanderer
E-mail- [email protected]


STOCK TANK POOL SUPPLIES

- Stock tank https://amzn.to/2tlkEiR or get a metal one at your local co-op
- Above Ground Pool Pump https://amzn.to/2H5pUwP
- Weatherproof Silicone Sealant https://amzn.to/2JQSNP9
- Hole Saw with Arbor https://amzn.to/2Xrpc8A
- Plunger Valves https://amzn.to/2IYjdwU
- Second Pool Outlet https://www.intexcorp.com/11235.html
(This outlet is out of stock, so these two pieces will work in it's place: https://bit.ly/2InHNK7 (You'll have to close off the hole with waterproof tape, as that part is out of stock) + https://amzn.to/2FvVO6F OR you can purchase THIS SET (https://amzn.to/2IHj8jR) and use only the parts you need from it.)
 - 1-3 Rubber Washers (or Gaskets) https://amzn.to/2WNk6PA
- Strainer Nut http://www.intexcorp.com/10256.html
- Chlorine Tablets https://amzn.to/2qAIFlr
- Floating Pool Dispenser https://amzn.to/2H6EbsP
- Water Testing Kit https://amzn.to/2Hs36uw



Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn't level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren't any unexpected leaks.
Step 2- Cut holes in your stock tank. I'm not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren't usually right on top of each other, but ours are. We haven't ever seen this as a problem.
Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn't put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it's going to be getting out, this is what will save you.
Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn't on full blast. You don't want to accidentally penetrate the sealant.
Step 6- Once you are sure there aren't any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren't any, fill the rest of the pool up!
Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that's okay, just be ready to screw it back on as soon as the water starts coming out.
+